Made with ScholarlyTurn your own files into documents like this
Fluid Mechanics — Fluid Properties: Viscosity
These notes are based on the retrievable portion of the video. The source transcript is partial, so topics not fully present—especially the complete liquid-temperature discussion, kinematic-viscosity definition, and some later exam problems—are marked accordingly.
Viscosity
Viscosity is a fluid property that resists flow, shear deformation, and relative motion between adjacent fluid layers. The resulting resistance appears as frictional or shear force when the fluid moves.
Ideal fluid: viscosity is zero.
Real fluid: has finite viscosity.
Cohesive force: attraction between molecules of the same fluid.
Adhesive force: attraction between different substances; do not confuse it with cohesion.
Molecular momentum exchange between neighboring layers also contributes to viscosity.
Newton’s law of viscosity
For a Newtonian fluid in laminar flow,
\[
\tau = \mu\frac{du}{dy}
\]
where:
\(\tau\) = shear stress
\(\mu\) = dynamic, absolute, or coefficient of viscosity
\(u\) = fluid velocity
\(y\) = distance normal to the layers
\(du/dy\) = velocity gradient
The original form is
\[
\tau = \mu\frac{d\phi}{dt}
\]
so shear stress is proportional to the rate of shear deformation.
Conditions
Use the relation when:
The flow is laminar.
The fluid is Newtonian.
Velocity varies with the normal coordinate only.
A Newtonian fluid has constant \(\mu\) at a specified temperature and pressure. Examples in the lecture include air, water, kerosene, petrol, and benzene.
Units and conversions
\[
1\ \mathrm{Pa\cdot s}=1\ \mathrm{N\cdot s/m^2}=1\ \mathrm{kg/(m\cdot s)}
\]
The CGS unit is the poise:
\[
1\ \mathrm{P}=1\ \mathrm{dyne\cdot s/cm^2}=0.1\ \mathrm{N\cdot s/m^2}
\]
For centipoise,
\[
1\ \mathrm{cP}=10^{-2}\ \mathrm{P}=10^{-3}\ \mathrm{N\cdot s/m^2}
\]
These conversions are used repeatedly in calculation questions.
Shear-stress graphs
For a Newtonian fluid, plotting \(\tau\) against the shear-rate \(d\phi/dt\) gives a straight line through the origin:
\[
\tau=\mu\left(\frac{d\phi}{dt}\right)
\]
The slope is \(\mu\).
For an ideal fluid, \(\mu=0\), so \(\tau=0\).
A larger slope means greater viscosity.
Viscometers
A viscometer measures fluid viscosity.
Efflux means outflow through an opening. A low-viscosity liquid flows out faster than a high-viscosity liquid; water therefore empties faster than honey.
Temperature effects
Gases
Gas viscosity increases as temperature increases. The dominant mechanism is increased molecular motion and momentum exchange. Approximate relations discussed include
\[
\frac{\mu}{\mu0}=\left(\frac{T}{T0}\right)^n
\]
and, as a kinetic-theory approximation,
\[
\mu_{\text{gas}}\propto\sqrt{T}
\]
For air, the lecture gives approximately \(n=0.7\). Temperature must be absolute temperature in kelvin. Molecular mean speed follows
\[
\bar V=\sqrt{\frac{3\bar R T}{M}}
\]
so increasing \(T\) increases molecular speed and momentum transfer.
Liquids
Liquid viscosity is strongly associated with cohesive forces. The supplied transcript does not contain the complete liquid-temperature explanation, so do not treat this section as complete.
Pressure effects
Under ordinary conditions, pressure has little effect on liquid viscosity because liquids are nearly incompressible. Gas viscosity is treated as primarily temperature-dependent and practically independent of pressure under ordinary conditions.
Calculation method
For a known velocity profile:
Differentiate the profile to obtain the velocity gradient.
Substitute into \(\tau=\mu\,du/dy\).
Convert all lengths and viscosity units to SI units first.
Check where the gradient is largest to locate maximum shear stress.
Example: velocity profile
If
\[
u=\frac{4}{3}y^{4/3}
\]
then
\[
\frac{du}{dy}=\frac{16}{9}y^{1/3}
\]
and
\[
\tau=\mu\frac{16}{9}y^{1/3}
\]
The transcript reports approximately \(0.65\ \mathrm{Pa}\) for its stated data, but the displayed expression and arithmetic are transcription-ambiguous; verify the original problem before using that numerical answer.
Example: pipe flow
Given
\[
u(r)=16\left(1-\frac{r^2}{R^2}\right)
\]
with radial coordinate \(r\),
\[
\frac{du}{dr}=-\frac{32r}{R^2}
\]
Thus the shear-stress magnitude is
\[
\tau=-\mu\frac{du}{dr}=\frac{32\mu r}{R^2}
\]
At the centerline, \(r=0\), so \(\tau=0\).
At the wall, \(r=R\), so \(\tau_w=32\mu/R\).
For \(D=1\ \mathrm{cm}\), \(R=0.005\ \mathrm{m}\), and water viscosity \(1\ \mathrm{cP}=10^{-3}\ \mathrm{N\cdot s/m^2}\),
\[
\tau_w=\frac{32(10^{-3})}{0.005}=6.4\ \mathrm{N/m^2}
\]
Therefore, the centerline stress is zero and the wall stress is \(6.4\ \mathrm{N/m^2}\).
Exam checklist
Identify whether the question uses \(du/dy\) or \(du/dr\).
Use the minus sign when velocity decreases in the direction of increasing radial coordinate; report magnitude if asked for shear-stress magnitude.
Convert \(\mathrm{cP}\), poise, centimeters, and millimeters before calculating.
For pipe flow, shear stress is zero at the centerline and maximum at the wall.
Do not infer that viscosity and density are directly proportional; the supplied transcript does not establish such a relation.
What to review next
The supplied material does not fully expose the later sections on liquid temperature effects, viscosity versus density, kinematic viscosity, pressure-related exam questions, or every worked problem. Review those sections in the video directly before relying on these notes for complete coverage.